Terex Advance Fd4000, Terex Advance Fd5000gl, Terex Advance Fd7000b, Terex Advance Fdc300, model year 2020. Filed by Terex Advance Mixer, Inc. and reported to NHTSA on 17 January 2020. 34 vehicles potentially affected.
What the notice says Terex Advance Mixer (Terex) is recalling certain 2020 FDC300, FD4000, FD5000GL, and FD7000B vehicles. The axle output shafts were incorrectly heat treated, possibly causing them to fracture.
Is your vehicle included? Check with your VIN at NHTSA, or ask a dealer. This page is an independent copy of the notice, kept so you can see what changed after it was published. It is not the authority, and the authority’s own text is the one to act on.
What owners ask about this recall
- Which vehicles does recall 20V023 cover?
- Terex Advance Fd4000, Terex Advance Fd5000Gl, Terex Advance Fd7000B, Terex Advance FDC300, model year 2020.
- What is wrong with them?
- Terex Advance Mixer (Terex) is recalling certain 2020 FDC300, FD4000, FD5000GL, and FD7000B vehicles. The axle output shafts were incorrectly heat treated, possibly causing them to fracture.
- What can happen if it is not put right?
- The fracturing of the output shaft would result in a loss of drive, increasing the risk of a crash.
- Is there a fix yet?
- Yes, and it is free. Terex has notified owners. Owners should inspect the Dana output flange for its production date. Dana will replace any that are in the affected range, free of charge. The recall began January 24, 2020. Owners may contact Terex customer service at 1-800-678-5961.
- What should I do now?
- Check your own vehicle by its VIN with NHTSA, which is the record to act on.
Answered from the register this site holds. NHTSA is the record to act on.
What the authority says can happen if this is not fixed: “The fracturing of the output shaft would result in a loss of drive, increasing the risk of a crash.”
affected
in the notice
caught
| Campaign | 20V023 |
|---|---|
| Filed by | Terex Advance Mixer, Inc. |
| System at fault | Power Train:Axle Assembly:Axle Shaft |
| Reported to NHTSA | 17 January 2020 |
| Model years | 2020-2020 |
| Vehicles named | TEREX ADVANCE FD4000, TEREX ADVANCE FD5000GL, TEREX ADVANCE FD7000B, TEREX ADVANCE FDC300 |
What the notice says today
The consequence
The fracturing of the output shaft would result in a loss of drive, increasing the risk of a crash.
The remedy
Terex has notified owners. Owners should inspect the Dana output flange for its production date. Dana will replace any that are in the affected range, free of charge. The recall began January 24, 2020. Owners may contact Terex customer service at 1-800-678-5961.
What it said before
This campaign is in the register but not yet in the dated wording archive, so we cannot yet say whether its text has moved. It enters the archive on the next pass.
This is one of 816 notices in the record whose component field names power train. Across that group the median wait before owners were written to was 42 days.
Last checked . No change has been recorded in the wording.
How to cite this record
Quoting the wording on this page means quoting a version, so the date belongs in the citation:
CarsMultiverse, recall 20V023, wording as read on 16 September 2026. https://carsmultiverse.com/recall/20v023/
The cross-border matches used on this site are deposited as a citable dataset: doi:10.5281/zenodo.22087136. The recall wording itself is published by the national authority named above and is theirs, not ours.
The recall record and its wording are published by the US National Highway Traffic Safety Administration and are US Government public domain. The dated archive, the comparison and any before-and-after above are CarsMultiverse. How fresh every engine behind this page is, is public on the status page. To check a specific vehicle, use NHTSA’s own VIN lookup.
Other Terex notices we hold
- 26V167: 2019-2026 General 65, General 80, General 95, C4000, C5000, and C6000 digger utility trucks equipped with pole guides
- 26V006: 2025 TL-Series, LT-Series, LTM40, HR40, HR46, and SCM55 areal device
- 26E016: pole position guide arm assembly pins with part number 450543
- 25V084: 2024 Commander
- 24V740: 2023-2024 TL80, TL80/112, TL100, and TM
- 24V526: 2020-2024 XT Pro
- 24V438: 2022-2023 TM
- 24V252: 2023 Commander
All 61 Terex campaigns we hold · Every manufacturer in the record
The fingerprint of this notice
We take a SHA-256 of each of the three blocks of text the authority publishes and keep the first eight characters. As we last read campaign 20V023 on 23 August 2026, they were:
- Defect summary
6722b6cf - Consequence
a7e64022 - Remedy
fce66c98
We first read this notice on 21 August 2026. It has not moved since. If it ever does, these characters will not match, and the change will be dated here.
The wording we hold for 20V023 · how the whole register is watched
Put this notice on your site
A small badge that links here and names the register's reference. It costs one line of HTML and needs no key.
The badge is free to use. It links to this page and nowhere else, and it never shows advertising.
Owners of these cars
No register publishes what happens after the letter. Owners do: tell us, in two taps.
Anonymous: no account, no cookie, nothing you type is stored beyond these choices. Figures appear once 3 owners have answered, and are published with the record under CC BY 4.0.